Olympia Chimney Chimney Cap Installation Nationwide

Olympia Chimney Chimney Cap Installation: The Greenwich Owner’s Guide

Olympia Chimney cap installation in Greenwich typically runs $260-$520 installed, including the replacement cap, stainless hardware, and a written photo record when we finish. We stock Olympia Chimney-compatible mesh and multi-flue caps on the truck, so most jobs are done in a single visit. The call usually starts the same way: you found pieces of rusted mesh in the yard after a storm, or you noticed a cap hanging at a tilt after the last nor’easter. By then, the cap has already been failing for a season, and the flue has been open to rain, leaves, and whatever the birds in backcountry Greenwich decided to bring in.

Call (516) 399-5497

Which Olympia Chimney Models This Applies To

Olympia Chimney is not a brand of chimney cap itself in the way most homeowners assume. Olympia Chimney makes flexible stainless steel liners, connectors, and termination kits for gas, oil, and wood-burning systems. The caps we install on Olympia Chimney terminations are matched to the specific liner diameter and flue type, not to a series name. That matching is where we see most owner mistakes.

The compatibility gotcha worth knowing: an Olympia Chimney gas liner termination uses a horizontal draft cap with a built-in spark arrestor, and that cap’s pipe diameter must match the liner exactly. If you have a 6-inch Olympia liner, a 7-inch cap is not “close enough” - it requires an adapter that some installers skip, and the first nor’easter pulls it loose. For wood-burning systems, we typically pair Olympia liners with a stainless steel multi-flue or single-flue mesh cap sized to the tile crown, not the liner. Corrine Halstead has pulled enough mismatched caps off Greenwich chimneys to tell you the honest version: the label on the old cap matters less than two measurements, the inner liner diameter and the outer crown dimensions.

We are an independent service provider, not affiliated with Olympia Chimney. We stock Olympia-compatible termination caps alongside parts from DuraFlex, HeatShield, and Gelco so we can match what is already on your chimney without ordering blind.

Signs Your Olympia Chimney Chimney Cap Installation Is Failing

Here is what a failing chimney cap actually looks like from the ground, before anyone puts a camera up the flue:

• Rusted mesh or missing mesh panels. The spark arrestor mesh is the first thing to go on any exposed metal part in coastal Connecticut. Once the mesh has holes, the cap is no longer keeping embers in or animals out. The underlying cause is salt air and freeze-thaw cycles, which chew through standard mesh in four to seven years.
• Water staining on the ceiling near the chimney. A tilted or missing cap lets rain run straight down the flue liner. Most Greenwich homeowners notice the stain before they notice the cap. What they are seeing is water that has already passed through the liner and into the surrounding framing.
• Debris, leaves, or nesting material at the fireplace opening. A cap that is loose or missing becomes an open invitation. Squirrels in Fairfield County do not need much of a gap. If you hear scratching and it is not the house settling, check the cap before you call an exterminator.
• A cap that is visibly tilted, lifted, or hanging from a bracket. Wind load on a multi-flue cap is real. The fasteners fail before the metal does. If the cap has shifted, the seal between cap and crown is compromised, and water is getting under it.
• Spalling crown or crumbling debris around the cap base. When the cap’s base plate sits in standing water or against a failing crown joint, the mortar around it starts breaking down. You will see sand-like grit on the roof or in the gutter near the chimney.

Before

After

Replacement Cost & What’s Included

For Olympia Chimney-compatible cap installation across Greenwich - Old Greenwich, Cos Cob, Riverside, and backcountry - the installed price range is $260 to $520. The spread comes from a few things: single-flue mesh caps sit at the low end, multi-flue caps with custom crown coverage run higher, and any cap installed on a chimney over 25 feet with steep roof access adds ladder and safety time.

Every quote is delivered in writing before any work starts, per Haven Standard Clause 1. That written price includes the cap, stainless mounting hardware, sealant work at the base, and the documented photo record we have kept on every job since 2009, Clause 4 of the Haven Standard. No surprises, no verbal add-ons after the fact. The work carries the 365-Day Done Right Promise: if the cap is not holding, installed square, and documented, we come back and make it right.

DIY or Call Us?

You can check a cap from the ground with binoculars. You should not be on a roof without proper fall protection, especially not a steep Greenwich colonial roof slick with moss or morning condensation. We have seen homeowners save the ladder fee and then drop a cap, crack a tile, or worse. The camera does not guess. Neither do we.

What you can safely do before calling: see if the cap is visibly tilted or missing panels, check inside the firebox for debris or nesting material, and take a photo of the liner opening from below if you have a clean view. What you should not do: climb onto the roof, step near the crown edge, or try to re-anchor a swinging cap with whatever hardware you have in the garage. A cap that catches wind mid-repair becomes a dangerous projectile. Call (516) 399-5497 and we will do the roof work, document the finished cap, and leave you with a written record of what was there and what we replaced.

FAQs